The Auto Rules
The Auto Rules
  • Видео 218
  • Просмотров 16 213 103
A Saturn Vue with a VTEC Problem
You might not have known that there were Saturns with VTEC. They just didn't call it VTEC. This is a 2006 Saturn Vue with a code P2647 causing the check engine light to illuminate.
Просмотров: 4 002

Видео

Chassis Noise Diagnosis with Chassis Ear
Просмотров 50 тыс.9 лет назад
This device is a fantastic tool for finding squeaks, creeks, pops, clicks, and grinds anywhere on the vehicle. If you can't tell exactly where a noise is coming from this tool can help.
Hyundai Timing Chain Tensioner Problem
Просмотров 296 тыс.9 лет назад
Hyundai 3.3 V6 engines have a problem with timing chain tensioners that loose the ability to hold pressure at rest. This causes a noise at start up. This shows the bad tensioner and exactly what it is doing.
Toyota Hybrid MG1 and MG2
Просмотров 19 тыс.9 лет назад
Another look at the magical unicorns found in the transaxle of the Toyota Prius. The Prius has no variable gear ratios between the traction motor and the final drive. This is a look at what that looks like.
Ford Expedition P0231 and Stalling Diagnosis
Просмотров 120 тыс.9 лет назад
This 2003 Ford Expedition with a 5.4 V8 stalls about every 5 to 10 minutes, and has a check engine light with the code P0231, fuel pump secondary circuit low. This is a common problem and this demonstration will show you how to diagnose the failure.
6.7 Powerstroke Low Fuel Pressure Problem
Просмотров 405 тыс.9 лет назад
After replacing the fuel filter the check engine light would illuminate and a message of "low fuel pressure" would show on the driver information display. Code P008A, "Low Pressure Fuel System Pressure Too Low" would show up on the scan tool. The fuel filter housing was not installed properly so it wouldn't bleed the air.
6.7 Powerstroke Broken Fuel Filter Housing
Просмотров 38 тыс.9 лет назад
Very common to brake the fuel filter housing on a 6.7 Powerstroke. This one might have been cross-threaded because it was leaking air into the low pressure fuel system before we tried to tighten it. The fuel filter was just replaced before it started having problems.
How does a Catalytic Converter Work?
Просмотров 259 тыс.9 лет назад
A brief description of what goes on inside a catalytic converter.
Piston Failure, 6.7 Cummins
Просмотров 33 тыс.9 лет назад
This piston melted down because of a leaky injector. If only someone could build an injector that would let this kind of expensive failure occur.
Retired Ambulance, 7.3 Powerstroke Quarter Mile, Lights On
Просмотров 11 тыс.9 лет назад
Because everyone wants to know how fast a tired ambulance with a diesel can run the quarter. This thing is slow but it's got low compression on all cylinders, a possible bad injector, and our dyno is at 6500 ft. above sea level (this is Wyoming after all) where you have to be really fast in order to be fast.
Looking at Diesel Exhaust Opacity
Просмотров 6 тыс.9 лет назад
Clean diesel technology is very clean. Even slightly older diesel technology is not that bad, but it is nothing compared to the newest engines. Check out the results comparing a 7.3 Powerstroke to a 6.7 Powerstroke.
Parasitic Load Testing
Просмотров 1,8 тыс.9 лет назад
A parasitic load, or key off battery draw will kill your car battery and can be very difficult to track down. If you follow a few simple steps it's not that difficult.
GT Car Racing Introduction
Просмотров 2029 лет назад
In the U.S. most race fans don't really know what GT car racing is. Let's take a look at at some of these cars racing in the Pirelli World Challenge at the Utah Grand Prix at Miller Motorsports Park. You can see just what kind of cars race in the upper classes of GT racing. This is some of the best stock car racing around and Miller is a fantastic track.
Power Steering Rack and Pinion Problems
Просмотров 471 тыс.9 лет назад
Rack and pinion powers steering with a few problems. When a bellows boot on the rack splits open it will cause problems. The leak follows the bad boot most of the time. This one also has bad outer tie rod ends.
Bad Strut Install Ruined Brake line
Просмотров 1,6 тыс.9 лет назад
If you put a car together the wrong way you will cause damage. This car had a strut mounted the wrong way and it caused the tire to rub through a brake line. Luckily for the drive the line blew out in their driveway.
Around the Garages Utah GP 2014
Просмотров 1549 лет назад
Around the Garages Utah GP 2014
Testing Starter Motor Current Draw
Просмотров 85 тыс.9 лет назад
Testing Starter Motor Current Draw
What Does a Bad Wheel Bearing Sound Like?
Просмотров 7 млн9 лет назад
What Does a Bad Wheel Bearing Sound Like?
Charging System Output Test
Просмотров 15 тыс.9 лет назад
Charging System Output Test
Brake Line Blowout
Просмотров 12 тыс.9 лет назад
Brake Line Blowout
Finding a Misfire with a Low Tech Power Balance Test
Просмотров 2,6 тыс.9 лет назад
Finding a Misfire with a Low Tech Power Balance Test
Touring Car Line Up, Utah Grand Prix 2014
Просмотров 559 лет назад
Touring Car Line Up, Utah Grand Prix 2014
Load Testing a Battery
Просмотров 33 тыс.9 лет назад
Load Testing a Battery
PCM Circuit Activation Testing
Просмотров 2,1 тыс.9 лет назад
PCM Circuit Activation Testing
Diagnosing O2 Sensor Heater Circuits P0161 and P0141
Просмотров 123 тыс.9 лет назад
Diagnosing O2 Sensor Heater Circuits P0161 and P0141
Bad Jeep Computer
Просмотров 212 тыс.9 лет назад
Bad Jeep Computer
Releasing the Throwout Bearing from a Pull-Type Pressure Plate
Просмотров 186 тыс.9 лет назад
Releasing the Throwout Bearing from a Pull-Type Pressure Plate
Features of an Automotive Specific DVOM
Просмотров 4549 лет назад
Features of an Automotive Specific DVOM
Using a Manually Ranging Meter
Просмотров 3,8 тыс.9 лет назад
Using a Manually Ranging Meter
Manually Ranging an Auto-Ranging Meter
Просмотров 2989 лет назад
Manually Ranging an Auto-Ranging Meter

Комментарии

  • @gypsyjman
    @gypsyjman 6 дней назад

    Please someone tell me ASAP I have the exact same problem but when I turn left, the noise completely goes away. What side do I need to replace?

  • @gypsyjman
    @gypsyjman 6 дней назад

    Please someone tell me ASAP I have the exact same problem but when I turn left, the noise completely goes away. What side do I need to replace?

  • @domenicozagari2443
    @domenicozagari2443 8 дней назад

    Let the heat from the radiator heat the vaporizer.

  • @jperez9528
    @jperez9528 10 дней назад

    So what I'm really hearing amongst the collective so far is that it likely wouldn't be a one time it's done fix but that likely a periodic repeat might prove more effective... The real question perhaps being how many times would it take, just as was the pun on the getting to the center of the "Tootsie Pop" of yesterday? Still the result that most stands out to me as it being a good process (albeit one perhaps more for the private owner like myself who simply doesn't care how long it takes nor how many times) is the reading that showed improved outflow to inflow... So if you got the money and just need the real fix quick make that play but otherwise turn on your best romance music and give that car the time and focused attention it deserves and who knows the car might not run but the women might flock to you and surely one of them will have a car while you busy fine tuning yours...😂🤷‍♂️😎😉

    • @jperez9528
      @jperez9528 10 дней назад

      "Do or Do Not, there is no try." - Yoda

  • @oguzhanguven4159
    @oguzhanguven4159 14 дней назад

    My prayers are for you brother

  • @jgrsocadagui2272
    @jgrsocadagui2272 21 день назад

    Excellent , thank you...

  • @oOLittleDevil
    @oOLittleDevil 21 день назад

    Changed the damn bearing, noise is still there the exact same. My press bolt broke when trying to take the bearing out so i had to resort to using a hammer although i didnt directly hit on the bearing and also placed it on an even metal plate to avoid damage. Could i have damaged it possibly ? Mine was also on the left side And also to my suprise the bearing i ordered was supposed to be made in germany but i noticed it said china on it when i wanted to put it in. Could be a fake ? Brand was FAG btw

  • @nicklanfear4303
    @nicklanfear4303 24 дня назад

    No steering wheel shimmy?

  • @tostadatheviking7828
    @tostadatheviking7828 27 дней назад

    My car's making a very mysterious noise like a metal slinky so I thought it might be a bad wheel bearing, evidently not

  • @aiiceejew
    @aiiceejew 28 дней назад

    Good video.

  • @mikegualjr
    @mikegualjr 29 дней назад

    Always thought was my tires haha

  • @jglaboratory
    @jglaboratory 29 дней назад

    I couldnt make mine do that turning...replaced bearing ...still same noise. Must be tire

  • @daeshod9591
    @daeshod9591 Месяц назад

    How can I tell the difference between bad brakes or bad bearings

  • @conorbuckley-wf1ke
    @conorbuckley-wf1ke Месяц назад

    Maybe if you didn’t talk so much we could hear it

  • @ellienhart5867
    @ellienhart5867 Месяц назад

    Can this happen right after an alignment??? My car wasn’t making that noice at all , I had new used tires put in and an alignment and it started making this noice , like an airplane taking off … and when the vehicle slows down a different noice

  • @rushzim
    @rushzim Месяц назад

    Sounds like rain on a metal roof.

  • @evensbolivar4110
    @evensbolivar4110 Месяц назад

    Thanks that's my problem

  • @leetos.4915
    @leetos.4915 Месяц назад

    exact same problem on my 2013 Honda accord MT due to my dumb mistake not putting back the top 4 screws on top of granny that connects the linkage cables and one of the two dowel pins fell inside the gears…I’m forced now to just replace the whole trans assembly…can’t find any 5th gear only for sell online to replace it

  • @taylorshea6856
    @taylorshea6856 Месяц назад

    It sounds and feels like my cars hitting the little rumble strips on the highway

  • @armandoduarte5501
    @armandoduarte5501 Месяц назад

    Same issue here today, 2013 6.7 I changed both fuel filters and truck run ok but Humming noice was there didn’t pay much attention cause was running ok. After driving 180 miles I got engine light, reduced engine power and low fuel pressure message. Watched some videos and pulled the left connector on the top fuel filter. Drain some fuel/air in to a plastic bottle and run ok for a few miles then I’ll do it again but problem won’t go away. I’m ready to retighten the bottom filter. Thanks for this video.

  • @zahircallicka1729
    @zahircallicka1729 Месяц назад

    Where did you source the rebuild kit from

  • @anncasey5903
    @anncasey5903 Месяц назад

    Thanks So Much! Very Helpful!🙂

  • @caseybee1.2.3
    @caseybee1.2.3 Месяц назад

    This is exactly what mine sounds like thank you!

  • @frannyjeffers6875
    @frannyjeffers6875 Месяц назад

    Do you get pulsing through the brake pedal?

  • @Abortabortgetouuuut
    @Abortabortgetouuuut Месяц назад

    Mine only makes that noise when I'm slowing down from 50+ mph, then when I'm at 10 to maybe 5 mph, I hear clicking or ticking noises from the same right front wheel. 2018 mitsubishi mirage g4 economy car with Cadillac prices for parts. I replaced a downstream o2 sensor and that sob was over 300 bucks

  • @jayk2k
    @jayk2k Месяц назад

    How was the remote trigger connected up and how did it have 12v to start with ? was it just connected to the battery in the car or another battery ?

  • @blessedhands2046
    @blessedhands2046 Месяц назад

    omg thank you so much i was wondering what sound i was hearing i thought my engine was gonna blow for a sec XD

  • @dominichicklen2028
    @dominichicklen2028 Месяц назад

    Great video my car is doing that now I’m just glad this video exist ! Thanks

  • @tiburon2781
    @tiburon2781 Месяц назад

    I have a hyundai Entourage. The motor has bracket or mount that is in the way of the timing cover. It almost seems like the engine is hanging off that bracket. I am not a mechanic but I think I can get this done. Do you know if the engine will drop if I remove the top bracket?

  • @PatTattsPowerChannel
    @PatTattsPowerChannel 2 месяца назад

    Dude thanks so much I thought I had a engine problem or bad spark plugs

  • @MotocrossRider155
    @MotocrossRider155 2 месяца назад

    All this time on my ranger I thought it was something rattling. Wow. This is exactly what it sounds like.

    • @kamryn7496
      @kamryn7496 Месяц назад

      Can’t figure it out my old engine made this noise I put a brand new long block 3.0 in my ranger an it still has detonation can’t be carbon buildup has to be something fuel related

  • @olskool501
    @olskool501 2 месяца назад

    Retired GM technician here I want to thank you so much for the clear information you have here. I fought with this damn thing for a couple of of hours before I looked up your video. When you said bolt the trans back up I knew I was on the right road from there. ✌️💯👍

  • @MrArtVein
    @MrArtVein 2 месяца назад

    Feels weird to say thanks for making my heart sink, but thanks 😢

  • @BeautywithSophie
    @BeautywithSophie 2 месяца назад

    I have this noise. I had all bearing replaced only to srill hear it. Next try is the gearbox bearing!! If its not that then i have no idea

  • @nd7968
    @nd7968 2 месяца назад

    Thank you for this video! My car is making this same noise. Do I suggest they take a look at my wheel bearing or see what they say and hope they come up with the same diagnosis? One place found nothing wrong, twice. But they only drove the car for a few minutes, no faster than 20 mph.

  • @erno9248
    @erno9248 2 месяца назад

    Thanks...

  • @erno9248
    @erno9248 2 месяца назад

    Thanks...

  • @USMCdad470
    @USMCdad470 2 месяца назад

    Followed the steps tightened it and now won’t start

  • @terjidjurhuus1917
    @terjidjurhuus1917 2 месяца назад

    This helped me find out that my car's strange sound is most likely not a bad wheel bearing. So thanks!

  • @fkturdo
    @fkturdo 2 месяца назад

    Always try and have at least 1/2 tank fuel when priming these things as well. I have seen them loaded and on low angle and sucking bubles but saying 1/4 full.

  • @Clemsonyotaman
    @Clemsonyotaman 3 месяца назад

    Try 50 dollars these days with inflation

  • @user-qd5tq8wk2z
    @user-qd5tq8wk2z 3 месяца назад

    Can it extract wheel bearing damage?

  • @devinbradshaw1977
    @devinbradshaw1977 3 месяца назад

    Sadly I now know I have to get fix it parts but thankfully you lead me right to the issue

  • @doorguru168888
    @doorguru168888 3 месяца назад

    Most of these vapor videos on youtube are seven, eight or nine years old and you never hear anything else. Conclusion: It does not work as far as saving gas.

    • @neurooracle5469
      @neurooracle5469 Месяц назад

      out of youtube , mine still working ( but not copying this video vapor setup ) my setup far more simple and safer ( no adding fuel tank in engine bay ) ..

    • @sirmagnus99
      @sirmagnus99 26 дней назад

      HHO and other alternative fuel videos all disappear about 10-12 years ago. I'd guess that's when big brother made the rounds, shutting down anyone commercialized the processes.

  • @keqcy9806
    @keqcy9806 3 месяца назад

    Yup mines like this do but around 40kmh it’s my left rear getting it fixed asap

  • @dbproductions2767
    @dbproductions2767 3 месяца назад

    Could it cause the car to vibrate? Or kinda shake? It shakes at different speeds.

  • @MrBonjito
    @MrBonjito 3 месяца назад

    I’m experiencing something similar but it is a higher pitch. It gets louder the faster the car is going but I do not hear a difference when moving the wheel while driving. Could this be something different?

  • @this92me
    @this92me 3 месяца назад

    This is front or rear bearing damage ?

  • @user-xj7dc1ms6v
    @user-xj7dc1ms6v 3 месяца назад

    Gasoline or Diesel?

  • @user-hr4jn2xn3o
    @user-hr4jn2xn3o 3 месяца назад

    Thanks so much